Spacez insight · March 2026 · 8 min read
Radiology & Medical Imaging Fitout Melbourne | Radiation Shielding, MRI & X-Ray Rooms
Radiology and medical imaging fitout specialists in Melbourne. X-ray, CT, and MRI room design, radiation shielding calculations, ARPANSA compliance, and NCC…
Radiology & Medical Imaging Fitout Melbourne
A radiology fitout is among the most technically demanding fitout types in the healthcare sector. It combines the standard NCC Class 9a healthcare construction requirements with a second regulatory layer — radiation safety — that requires specialist engineering, purpose-built construction, and compliance with both Commonwealth and state radiation safety legislation.
The radiation shielding design alone can add $50,000–$300,000 to a fitout cost, depending on the modality (X-ray, CT, fluoroscopy, nuclear medicine, MRI) and the occupancy of adjacent areas. Getting this design wrong can result in failed ARPANSA compliance and the inability to operate.
Spacez works with specialist radiation physicists and qualified radiation engineers to deliver compliant diagnostic imaging fitouts across Melbourne — from a single GP X-ray room to a multi-modality diagnostic imaging centre.
Regulatory Framework
Radiation Safety Legislation (Victoria)
In Victoria, radiation sources (including medical X-ray equipment, CT scanners, fluoroscopy units, and nuclear medicine sources) are regulated under the Radiation Safety Act 1975 (Vic) and the Radiation Safety (General) Regulations 2007 (Vic). The relevant regulator is the Department of Health (Vic) through its Radiation Safety unit, with oversight from the Australian Radiation Protection and Nuclear Safety Agency (ARPANSA) for Commonwealth regulatory functions.
Key regulatory requirements affecting the fitout:
- Licence for possession and use of radiation apparatus — issued by the Victorian Department of Health
- Radiation management plan — required before the practice can operate; the fitout design must be consistent with the management plan
- Shielding design approval — a radiation shielding design prepared by a qualified medical physicist or radiation engineer must be submitted to the Department of Health for approval before construction
- Shielding verification — post-construction radiation survey by a qualified physicist to verify that the constructed shielding meets the design specification
NCC Classification
A diagnostic imaging centre is classified as a NCC Class 9a (healthcare) building. This imposes:
- BCA compliance for healthcare buildings (infection control, accessibility, emergency management)
- Specific requirements for patient areas, staff areas, and radiation controlled areas
- Fire safety, egress, and DDA (Disability Discrimination Act) compliance
Modalities and Their Fitout Requirements
X-Ray (Radiography)
A standard diagnostic X-ray room is the most common radiation environment in a fitout context — used in general practice, specialist medical, dental, and veterinary settings.
Room size: A standard radiography room requires a minimum floor area of approximately 3.6m × 4.0m clear (14.4 sqm), with additional space for patient transfer, equipment positioning, and the operator console area outside the controlled zone.
Radiation shielding: The shielding design depends on the X-ray equipment's operating kVp, mA range, workload (number of exposures per week), and the occupancy of adjacent areas:
- Walls: Lead sheet (typically 1.0–2.0mm Pb equivalent) bonded to plasterboard, or equivalent in concrete or barium sulfate plaster
- Floor/ceiling: Calculated based on the above/below occupancy — may require lead sheet or additional concrete
- Door: Lead-lined door with overlapping lead sheet at the frame
- Window (observation): Lead glass panel at the operator console
Operator console: The X-ray operator must be positioned in a controlled area (typically behind the lead-shielded wall or in a separate operator booth) while exposures are made. A lead glass observation window allows the operator to see the patient.
Power: Standard diagnostic X-ray units require a dedicated high-current power supply (typically a 30A or 50A single-phase or three-phase circuit) — confirm the specific requirement with the equipment supplier.
CT Scanner
A CT (Computed Tomography) scanner room is significantly more demanding than a standard X-ray room:
Room size: A CT scanner room requires approximately 5.0m × 6.0m clear minimum — some modern large-bore or dual-energy CT systems require more. Plus an equipment room for the computer/cooling hardware (typically 2.5m × 3.0m adjacent to the scan room, with cable penetrations).
Structural requirements: A CT scanner weighs 1,500–3,000kg depending on the model. The floor must be structurally engineered to carry this load — typically a reinforced concrete slab or a structural steel framing system. For upper-floor fitouts, a structural engineer's assessment and possibly significant structural upgrades are required.
Radiation shielding: CT scanners produce significantly higher scatter radiation than standard X-ray units. Shielding calculations are more complex and typically result in heavier shielding requirements:
- Lead sheet walls of 2.0–3.5mm Pb equivalent, or equivalent in dense concrete
- Lead-lined doors (heavy; power-assisted opening is standard)
- Special attention to the orientation of the scanner gantry within the room
Cooling and HVAC: CT scanners generate significant heat (the X-ray tube and power electronics). The equipment room requires dedicated cooling (typically a dedicated precision air conditioning unit for the equipment room plus standard HVAC for the scan room).
Quench pipe (for MRI-adjacent fitouts): Not applicable to CT, but note that MRI quench pipes are a separate requirement.
MRI (Magnetic Resonance Imaging)
MRI fitouts are the most complex in diagnostic imaging — combining RF (radiofrequency) shielding with magnet safety requirements and cryogen management. MRI does not produce ionising radiation but has its own unique hazard profile.
RF shielding (Faraday cage): MRI scanners transmit and receive radiofrequency signals at precise frequencies. External RF interference degrades image quality; the MRI room must be enclosed in an RF shield (a Faraday cage) — typically copper or aluminium foil sheets bonded to the room structure with specialist RF-welded joints, penetrations, and an RF-shielded door.
This is specialist work — not standard electrical shielding — and must be designed and constructed by an MRI RF shielding specialist.
Magnetic field: A modern clinical MRI system (typically 1.5T or 3.0T field strength) has a significant fringe magnetic field extending beyond the scan room. The 5 Gauss line (the boundary within which the field can affect pacemakers and other implanted devices) must be contained within the controlled area. Site planning must account for the location of public areas, offices, and service corridors relative to the 5 Gauss line.
Structural elements near the scanner (beams, columns, reinforcing) must be non-ferromagnetic — or the scanner siting must account for the effect of ferromagnetic structural elements on field homogeneity.
Cryogen management: Superconducting MRI systems use liquid helium as a cryogen. In a quench event (rapid venting of cryogen), large volumes of helium gas are discharged. A quench pipe must be routed from the magnet through the building to the outside — typically 150mm diameter, with a designated termination point away from air intakes and public areas.
Access and installation: A whole-body clinical MRI system cannot be installed through a standard door. Planning must allow for a knock-out panel or oversized access opening that can be reconstructed after the magnet is moved into position using a specialised rigging contractor.
Fluoroscopy
Fluoroscopy (real-time X-ray) rooms are used for procedures (GI radiology, interventional, barium studies) and require:
- Overhead fluoroscopy X-ray tube with image intensifier — ceiling rail mounting or floor mounting (requires heavier floor loading and ceiling structural support)
- Higher workload than standard radiography → typically heavier shielding
- Often larger rooms to allow for interventional access around the patient table
Nuclear Medicine / PET-CT
Nuclear medicine and PET-CT involve the administration of radioactive pharmaceuticals to patients, creating a different radiation safety challenge — the patient becomes a radiation source after dosing, not just during imaging:
- Dedicated hot lab (radiopharmacy area) for preparation of radiopharmaceuticals — significant shielding and ventilation requirements
- Lead-shielded storage for radioactive material
- Patient waiting area designed to minimise scatter to adjacent areas
- Decay storage for radioactive waste
- This requires specialist nuclear medicine fitout experience beyond standard X-ray shielding
Key Design Considerations
Radiation Physicist Engagement
A qualified medical physicist (or radiation engineer) must be engaged at the design stage — not after construction. The physicist:
- Calculates the required shielding for each room based on the specific equipment, workload, and adjacent area occupancy
- Prepares the radiation shielding design documentation for Department of Health submission
- Specifies the shielding materials and installation requirements
- Conducts the post-construction radiation survey
Do not select a fitout builder who proposes to design the shielding in-house unless they have a registered physicist on staff. Shielding design requires specific equipment, software, and professional registration.
Lead Sheet Installation
Lead sheet is the most common shielding material for X-ray rooms in commercial fitouts:
- Lead sheet is heavy (approximately 11,340 kg/m³) — even 1.5mm Pb is approximately 17 kg/m² of wall area
- Installation requires bonding to plasterboard with specialist adhesive and fasteners
- All joints, penetrations (power outlets, data, HVAC ducts), and frames must be lead-wrapped with overlapping lead sheet to prevent any unbridged gaps
- The overlap at joints is critical — a 10mm unbridged gap can create a significant radiation path
Lead sheet is typically installed by a specialist lead lining contractor, not a standard fit-out carpenter.
HVAC and Ventilation in X-Ray Rooms
Standard HVAC ducts passing through a radiation-shielded wall create a radiation path if not addressed. Solutions:
- Route ducts to avoid penetrating shielded walls where possible
- Where penetration is necessary, line the inside of the duct with lead sheet for the required distance on each side of the wall
- Use transfer ducts positioned so the radiation path through the duct bends at least 90° (reducing direct radiation paths)
Fitout Cost Guide — Melbourne 2026
| Room Type | Size | Cost (excl. equipment) |
|---|---|---|
| Single GP X-ray room | 20–35 sqm | $80,000–$180,000 |
| Standalone X-ray/radiography suite (1–2 rooms) | 50–120 sqm | $200,000–$450,000 |
| CT scanner room + equipment room | 80–150 sqm | $350,000–$900,000 |
| MRI room (RF shielding + Faraday cage) | 80–180 sqm | $500,000–$1,500,000+ |
| Full diagnostic imaging centre (X-ray + CT + MRI) | 400–1,000 sqm | $1,200,000–$4,000,000+ |
Lead shielding cost: $200–$600/sqm of shielded wall area depending on Pb thickness.
RF shielding (MRI): $150,000–$400,000 for the Faraday cage construction and specialist penetrations.
Physicist fees: $8,000–$30,000 for design, documentation, and post-construction survey.
Structural engineering (CT/MRI floor): $5,000–$30,000 for assessment and design; structural works variable.
Frequently Asked Questions
Do I need a radiation physicist before I sign a lease for a radiology fitout?
Yes — before committing to a tenancy for a radiology fitout, a physicist should assess the building's structural suitability (floor loading for CT/MRI), the feasibility of shielding to adjacent occupied areas, the quench pipe routing path (for MRI), and access for equipment installation. Discovering a structural or shielding feasibility problem after signing a lease can be extremely costly.
Can a standard fitout builder construct the radiation shielding?
The structural construction (walls, floors, ceilings) can be completed by a qualified commercial fitout builder. The lead lining installation is specialist work and is typically subcontracted to a specialist lead lining contractor. The RF shielding (for MRI) must be completed by a specialist RF shielding contractor. Spacez coordinates the full team including physicists, lead liners, and RF shielding contractors as part of the project.
How long does a radiology fitout take?
A single X-ray room fitout takes approximately 8–14 weeks from design approval. A CT scanner room adds structural and equipment integration complexity — typically 14–22 weeks. An MRI fitout (including RF shielding and magnet installation) typically runs 20–36 weeks. Allow additional time for regulatory approvals (shielding design approval from Department of Health: 4–8 weeks) and post-construction physicist survey before operation commences.
Spacez delivers radiology and diagnostic imaging fitouts across Melbourne — coordinating radiation physicists, lead lining contractors, and RF shielding specialists alongside our commercial fitout capability. Contact us to discuss your imaging centre project.